1.
.buka cisco packet tracer
2.
Lalu buatlah topologi seperti di bawah ini
gambar lebih jelas
3. Ungu:vlan
10
Nama:tkj
Gateway
192.168.100.10
Kuning :vlan 20
Nama :rpl
Gateway
192.168.200.10
4. Anda
harus setting ip computer
5. Missal
pc 0,1,4,5 =vlan sepuluh selainnya vlan 20
6. Buatlah
vlan di switch kiri dulu, lalu dibuat
trunk
Vlan 10
Switch>en
Switch#conf t
Enter
configuration commands, one per line. End with CNTL/Z.
Switch(config)#int range fa0/1-2
Switch(config-if-range)#sw mode acc
Switch(config-if-range)#sw
acc vlan 10
Vlan 20
Switch(config)#int range fa0/3-4
Switch(config-if-range)#sw mode acc
Switch(config-if-range)#sw
acc vlan 20
Buat trunk
Switch(config)#int fa0/4
Switch(config-if)#sw
mode trunk
7. Buat
vlan switch kanan
Switch>en
Switch#conf t
Enter
configuration commands, one per line. End with CNTL/Z.
Switch(config)#int range fa0/2-3
Switch(config-if-range)#sw mode acc
Switch(config-if-range)#sw
acc vlan 10
Vlan 20
Switch(config)#int range fa0/4-5
Switch(config-if-range)#sw mode acc
Switch(config-if-range)#sw
acc vlan 20
Buat mode trunk
Switch(config)#int fa0/6
Switch(config-if)#sw
mode trunk
Yang di beri
warna orange adalah interface yabg terhubung switch
8. Setting
router,
Hidupkan router
agar nyala caranya itu
pilih interface yang terhubung
lalu buat no sh
Router>ena
Router#conf t
Enter configuration commands, one
per line. End with CNTL/Z.
Router(config)#int g0/0
Router(config-if)#no sh
Lalu anda harus mengatur ip router yang sesuai dengan
gateway VLAN
-setting inter Vlan 10
Router#conf t
Enter configuration commands, one
per line. End with CNTL/Z.
Router(config)#int g0/0.10
Router(config-subif)#
%LINK-5-CHANGED: Interface
GigabitEthernet0/0.10, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol
on Interface GigabitEthernet0/0.10, changed state to up
Router(config-subif)#enca
Router(config-subif)#encapsulation
do
Router(config-subif)#encapsulation
dot1Q 10
Router(config-subif)#ex
-setting inter Vlan 20
Router(config)#int g0/0.20
Router(config-subif)#
%LINK-5-CHANGED: Interface
GigabitEthernet0/0.20, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol
on Interface GigabitEthernet0/0.20, changed state to up
Router(config-subif)#enca
Router(config-subif)#encapsulation
do
Router(config-subif)#encapsulation
dot1Q 20
Router(config-subif)#ex
Sekarang beda VLAN sudah bias PING
Catatan:
a. Yang diberi arna merah di beri angka
sesuai vlan yang di atur
b. Yang di beri warna biru di atur no sh sesuai interface yang terhubung
Selesai………………………………………………………………….
